NJ BMW CCA Toolbox
NJ folks (Plaz, Kognito)
Did you know the NJ BMW CCA chapter has a "toolbox" where members can borrow stuff for free? I posted asking about a spring compressor, and it turns out they have a TON of stuff (scales for corner balancing too :eeps: ) New Jersey Chapter - Toolbox Contents Tool Description Tool Details / Comments M Engine Valve Adj Tool and Shim Set Not for M50 engines Engine Turning tool/Single Row Chain Sir BMW3015 (BMW 113114/5) Engine Turning tool/Double Row Chain Sir BMW3016 Valve Spring Compressor/Single KD-383 Profile Gasket Cam Tool (1.8/16 valve M42 engine) 0 Head Compression Frame/4 cyl. M10 0 Compression Tester Peerless s/n 830912171 Torque Wrench - beam type 0 - 100 ft-lb 0 Torque Wrench - beam type - 0 - 140 ft-lb 0 Clutch Alignment Tool 0 Engine Hoist 0 17mm/14mm Curved Box Wrench 0 30 mm ½" Deep Socket/Thin Wall Snap-on 1-3/16" 6-pt TS-382 17 mm Allen Wrench/Gearbox Drain Plugs 0 1-7/16" (36mm) 3/4" drive socket Williams 3/4" drive ratchet Thorsen 790 10" HD Kukko Puller (for Flanges, Hubs, etc) 0 Peake R5/fcx Fault Code Reader Peake R5/fcx Peake R5 Reset tool Peake R5 Service Interval Reset Tool AST-BMW 6211 with MNW 6212 adaptor Exhaust Gas Analyzer CO/HC (reads CO only) ST-500 Exhaust Gas Analyzer CO #1 AFR Heathkit C1-1080 Exhaust Gas Analyzer CO #2 0 Timing Light w/Advance Snap-on MT-241 s/n 30797 Timing Light Heathkit C1-1040 Tach/Dwell Meter Heathkit CM-1073 Yokogawa Mini Digital Multi Tester 2447-01 McPherson strut spring compressor Branick Tie Rod Separator (BMW Factory Tool) 0 Center Track Rod Separator (BMW Factory Tool) Sir BMW3032 (BMW 31 1 140 CE 90) Rear axle carrier bushing kit Sir tools BMW-3026 Wheel bearing replacement kit Sir Tools B90-BMW 320i Ball Joint Separator (BMW Factory Tool) 0 318/325 (E30) Series Ball Joint Separator (BMW Factory Tool) 0 Racing scales (4 pads, electronic controller) 0 OTC Injector Cleaner OTC Injector cleaner fluid for OTC OTC CIS Injection System Tester TU-113 Multi Carb Syncronization Tool Unitest 2-port Pressure Brake Bleeder/Prof. Reservoir w/Diaphram Type 0 Manual 1602 - 2002 Sedan 0 Manual 2500 - 3.0CS Coupe 0 Manual 2500 - 3.3L Sedan 0 Manual 320i Sedan 0 Manual 530i Sedan (2) 0 Manual 528i & 530i Sedan (HAYNES Manual) 0 Manual Manual 318i Sedan 0 Manual Parts Manuals (all BMW Factory) 0 Manual 1500 - 1800TI/TISA Sedan 0 Manual 1500 - 2000 Sedan 0 Manual 1602 - 2002 Sedan 0 Manual 2500 - 3.0S Sedan 0 WEBER Carb Repair/Setup Manual - Haynes 0 BMW Fuel Injection/An Enlightened Approach - Metric Mechanic 0 BMW K-Jetronic F/I Manual (BMW Factory Manual) 0 |
Cool! NCC supposedly has some stuff, but I've never seen a list.
|
Terry has some catching up to do :twisted:
|
Holy crap!
I wonder if their torque wrenches have been set to 88 ft-lbs for over a year, too. :eeps: |
Quote:
I hope no one pours that OTC shit into their fueltanks. :eeps: |
Quote:
Quote:
|
Quote:
(Please don't forget I'm a clueless newbie.) |
Quote:
There are certain jobs that can only be done with a beam-type (ie, one particular step in rebuilding a final drive). |
Quote:
|
Quote:
|
All times are GMT -4. The time now is 05:07 PM. |
Powered by vBulletin® Version 3.7.1
Copyright ©2000 - 2024, Jelsoft Enterprises Ltd.
Forums © 2003-2008, 'Mudgeon Enterprises - Site hosting by AYN & Associates, LLC